XYZ/IJK Location/Rotation

Changes the instrument’s location and rotation; the instrument labels rotate with the instrument unless Right-Reading was selected in the Label Legend Manager (see Formatting the Label Legend). In a 3D view, if an instrument is associated with a focus point, the instrument, along with any accessories, rotates automatically so that it points to the focus point.

Edit

Opens the Lighting Device dialog box, for editing the parameters of one or more lighting devices

Device Type

Displays the type of object that is selected; normally, instruments are Light device types (Moving Light, Device, Practical, SFX, Power, and Other are also considered Light types). Accessories such as color frames, barn doors, and top hats are Static Accessory types; accessories that require a control channel, such as color scrollers, are Accessory types.

Instrument Type

Displays the specific type of lighting instrument

Wattage

Indicates the power consumed by the instrument

Purpose

Specifies the purpose for using

Position

Displays the name of the lighting position

Unit Number

Identifies the instrument location on the lighting position

Color

Specifies the gel color number according to manufacturer code, RGB values, color name from the file, or web (hex) codes; when the light associated with the instrument is turned on, Color specifies the actual light color. Use + between color numbers to indicate combinations of two or more colors. See Lighting Instrument Color

The color setting can affect the display of the lighting device color, depending on the Spotlight preferences. See Lighting Device Setup

Dimmer

Specifies the dimmer or DMX address number of the instrument

Channel

Specifies the channel number of the instrument

Address

Specifies the absolute address of the instrument. If Automatically assign Universe is selected in the Spotlight Preferences dialog box, this field is used to automatically populate the Universe and U Address fields.

Universe

Indicates the DMX group of the dimmer; this is set automatically if the Spotlight file is set up to assign the universe. See Universe Assignment in Vectorworks Spotlight

U Address

When the universe is automatically assigned, displays the address assigned within the universe

Circuit Number

Indicates the circuit number where instrument is plugged in

Circuit Name

Specifies the name of bundled circuit group

System

Specifies the letter describing the control system (Lightwright-compatible parameter)

User Field 1 – 6

Provides user-defined fields; use these extra fields to keep track of any desired data (see Specifying Lighting Device Parameter Display)

Num Channels

Identifies the number of control channels used by the instrument

Frame Size

Indicates the dimensions of the color cut

Field Angle

Sets the field angle of the instrument’s light beam

Field Angle 2

Specifies the second field angle for an elliptical light source

Beam Angle

Sets the beam angle of the instrument’s light beam

Beam Angle 2

Specifies the second beam angle for an elliptical light source

Weight

Specifies the instrument weight

Gobo 1

Indicates the gobo texture number for the first gobo

Specifying the gobo texture by clicking Edit in the Object Info palette provides a graphical method of selecting textures from the default content

Gobo 1 Rotation

Sets the rotation angle of gobo texture 1

Gobo 2

Indicates the gobo texture number for the second gobo

Gobo 2 Rotation

Sets the rotation angle of gobo texture 2

Gobo Shift

Adjusts the position of the instrument gobos to the front or rear

Mark

Provides a user-defined label (Lightwright-compatible parameter)

Draw Beam

Select to draw an accurate wireframe representation of the light beam; the light beam is drawn based on the instrument parameters, and can be used to check whether the stage and focus areas have been adequately lit (see Drawing Light Beam Representations). Spotlight setup can globally specify the appearance and display of the elements in the light beam (angles and centerline).

Draw Beam as 3D Solid

Generates a light beam that appears solid when rendered

Use Vertical Beam (Focus Point required)

By default, draws the wireframe beam in a vertical orientation when possible, when either Draw Beam or Draw Beam as 3D Solid is selected. When deselected, the beam is usually drawn in a horizontal orientation.

Show Beam at

In a 2D view, select whether to draw the beam as it crosses the focus point, at the falloff distance as projected through the focus point, or in both areas

Replace with Active Symbol

Replaces the selected instrument with the current active symbol (see Replacing Instruments )

Refresh Labels

Refreshes instrument labels if label changes have been made

Falloff distance

Specifies how far the wireframe light beam is drawn beyond the focus point; the Focus Instruments command sets this value to the distance between the focus point object and 0

Lamp Rotation Angle

Indicates the rotation angle of the virtual elliptical light source, from 0 to 90°

Shutter parameters

Controls the angle and depth of top, left, right, and bottom shutter cuts. Each shutter is located at 90º intervals around the lighting instrument, and can be adjusted +/- 45º. The shutter depth ranges from 0 to 100%, with 100% cutting through the center of the light source.

Symbol Name

Displays the name of the symbol used to create the instrument or accessory

Use Legend

Select the label legend to apply from the list of label legends in the file (see Using the Label Legend Manager)

Automatically Flip Front & Back Legend Text

Select to mirror the label legend along the X axis of the lighting instrument

Automatically Flip Left & Right Legend Text

Select to mirror the label legend along the Y axis of the lighting instrument

Focus

Specifies the focus point for the lighting instrument. The focus point must be defined first (see Focusing Instruments).

Set 3D Orientation

Specifies the X/Y position of the instrument at the hanging point, for 3D views only